How to Use a Surface Planer | Woodworking

Watch more Learn Woodworking videos:

Learn how to use a surface planer in this Howcast woodworking video featuring Makeville Studio.

Surface planer is one of several tools that you’ll need in a shop if you’re going to mill and square up rough lumber, but it also has a separate function which is just to reduce the thickness of boards so you can use it as a thickness planer and also as a surfacer.

If you use it as a thickness planer it is pretty simple to operate. The basic way this is setup is there is a set of blades in the middle of this housing and there is a couple rollers and so you pass the board in and it gets grabbed by the roller, goes under the blades, comes out on the other roller and the blades are skimming off material as its passing through. It can skim off up to an 16th or even an 8th of an inch, that’s pretty aggressive at one pass. Normally what you’re doing is passing a board through multiple times to skim off the little bits of material until you get down to the thickness that you want. The way it works is there is a crank on the side which raises and lowers this entire housing, that’s essentially changing where the blade height is. You need to setup that up first when you’re working with a board. You have to know how thick a board you have. You can measure it and set the height on this gauge here or you can measure it by feel which is what I do. I actually put it in the machine and start lowering it and I’ll feel when it starts to hit the rollers and other mechanisms underneath the housing.

When I hit the roller I will back off a little bit and then I know that I’m probably at the surface of the wood at this point. From there I will go a half turn and I know I will be taking off probably about a 16th of an inch. Now, there’s a couple of options for setting controls on here. You can go between two types of finishes. One is called finishing cut and one is called dimensioning. Essentially, switching between these two positions usually speeds up or slows down the rollers so either you’re getting more cuts per inch or fewer cuts per inch depending on the setting. More cuts per inch make a finer finish so you can use that for a finish cut.

Another control that is pretty useful on this machine is a depth stop. You can use this to set a depth you don’t want to go beyond. Lets say I have this board, its one and a quarter inches, I only want to go down to an inch. It is very easy to go past an inch sometimes if you’re not being careful with this wheel, what this does is it prevents this wheel from turning once it gets down to one inch, you can’t even turn the wheel anymore. That’s useful, if you’re not using that just put it down to some low dimension that you’ll never get to and you’ll never be stopped.

Now one thing that is really important on surface planers is dust collection. These machines make a huge amount of dust and this machine particularly ejects that dust at a high velocity. So that machine next to us, the dust collector, has to be on when this is on otherwise you get a big mess of dust in the shop. That’s it for the setup of this machine. I’m going to run this board through to see how it works. One thing you’ll want to do when you’re running a board through the planer is draw some lines on it just so you can your progress. Sometimes the top surface of the board may have some hills or valleys maybe cupped. One of the things you need to be aware of with this machine is that it only works if you have one flat face already. What happens is it references off the bottom face which is on this bed down here and it takes whatever it reads down there and does it to the top face. So if you have a bow or twist in your board as this is passing through the planer it is going to get pushed down by the roller and it’s just going to accentuate the shape of whatever board you have. It’s not a magic box. It just doesn’t make a flat piece of wood out of a twisted one. You need to actually have one flat faced before bringing your wood over here. Once you do then you’re ready to go.

This machine is extremely loud and you will want to wear ear protection when using it. Okay, that’s our finished product and I wanted to run this through to show you one other thing about the planer which is something that happens a lot. It’s called snipe. I don’t know if you can see this but there is a slight difference in height where the planer blades have chunked out a little bit extra on these last couple of inches of the wood. What happens is when passing the wood through there, the roller grabs it and actually pulls it up into the blade. So at the beginning and at the end of the cuts, the roller does that, it pulls it up into the blade. Y
Video Rating: / 5

221 – TWW Live: Are You a Maker or a Woodworker?

Original post on our site with additional information, details & comments:

Welcome to the first in a new series of live shows called TWW Live! The latest news, reviews, and your projects and questions.

– Last Month’s Winners: Janet B. (Festool CT36 Vac and ETS150 Sander) and Brian R. (3M Safety Bundle)
– This Month’s Giveaway, Enter Now:
Arbortech Mini Grinder:
Fuji Mini-Mite3 Turbine HVLP:

– The Great Bessey/Lowes Feeding Frenzy of 2014: Ryan Royal gets the “no-prize.” He picked up 32 worth of clamps for just 0!

Featured Project
– Anna’s Hope Chest by Steve Boudreau:
– Submit Your Project:

– Chuck Hampton wonders if we need another video series that shows projects and answers questions.
– Chris is trying to decide if he’s a Maker or a Woodworker, after reading this Nerdist article:
– Ashley has some insightful thoughts about what makes a Maker a Maker.

In Case you Missed It
– Bill Doran – Leatherman Pouch:

– Adam Savage – Why We Make:

Gear Up!
– Check out the new SENCO FinishPro 21LXP 21 gauge brad nailer:

Learnin’ Time
– Woodworks Season V:

In the Shop
– A beautiful jewelry box collaboration project with Gary Rogowski.
– Bending forms for the Morris Chair.

– WatchingDragon – “How do you cut wood for a wooden tankard with only hand tools?”
– Jonathan – “When burning wood scraps, are there any types that are dangerous?”
– Eric – “Suggestions for a good cheap readily-available wood for a beginning woodworker?
– Matt – “Have you ever had the problem that you spend the majority of time building things for the shop?”
– JC – “Any suggestions for finishes for children’s toys?”

Tune in to the next show on Wednesday, July 2nd at 1pm Eastern!

The Wood Whisperer is education and entertainment for the modern woodworker! Find more at & don’t forget to subscribe to our YouTube channel!

Connect with us!
Follow us on Twitter
Like us on Facebook
Pin us on Pinterest

Learn more about our premium project videos at
Video Rating: / 5